LCD Programming Example using 'C'

Eight-bit interface using the busy flag.

If you feel that you want to learn how to implement the use of the busy flag then you should do this first with an eight-bit interface. This version allows you to use any available I/O pin for any of the signals. There are now three control lines so you will need eleven I/O pins.

The source code is here.
A similar program written in Assembly Language is here.
A similar program written for the Arduino IDE is here.
The list of all LCD programming examples is here.

/**************************************************************************** LCD-AVR-8f.c - Use an HD44780U based LCD with an Atmel ATmega processor Copyright (C) 2013 Donald Weiman (weimandn@alfredstate.edu) This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ /**************************************************************************** File: LCD-AVR-8f.c Date: September 16, 2013 Target: ATmega328 Compiler: avr-gcc (AVR Studio 6) Author: Donald Weiman Summary: 8-bit data interface, with busy flag implemented Any LCD pin can be connected to any available I/O port Includes a simple write string routine. */ /******************************* Program Notes ****************************** This program uses an 8-bit data interface and it uses the busy flag to determine when the LCD controller is ready. The LCD RW line (pin 5) must therefore be connected to the uP. The use of the busy flag does not mean that all of the software time delays have been eliminated. There are still several required in the LCD initialization routine where the busy flag cannot yet be used. These delays are have been implemented at least twice as long as called for in the data sheet to accommodate some of the out of spec displays that may show up. There are also some other software time delays required to implement timing requirements such as setup and hold times for the various control signals. *************************************************************************** The eight data lines as well as the three control lines may be implemented on any available I/O pin of any port. These are the connections used for this program: ----------- ---------- | ATmega328 | | LCD | | | | | | PD7|---------------->|D7 | | PD6|---------------->|D6 | | PD5|---------------->|D5 | | PD4|---------------->|D4 | | PD3|---------------->|D3 | | PD2|---------------->|D2 | | PD1|---------------->|D1 | | PD0|---------------->|D0 | | | | | | PB1|---------------->|E | | PB2|---------------->|RW | | PB0|---------------->|RS | ----------- ---------- **************************************************************************/ #define F_CPU 16000000UL #include <avr/io.h> #include <util/delay.h> // LCD interface (should agree with the diagram above) #define lcd_D7_port PORTD // lcd D7 connection #define lcd_D7_bit PORTD7 #define lcd_D7_ddr DDRD #define lcd_D7_pin PIND // busy flag #define lcd_D6_port PORTD // lcd D6 connection #define lcd_D6_bit PORTD6 #define lcd_D6_ddr DDRD #define lcd_D5_port PORTD // lcd D5 connection #define lcd_D5_bit PORTD5 #define lcd_D5_ddr DDRD #define lcd_D4_port PORTD // lcd D4 connection #define lcd_D4_bit PORTD4 #define lcd_D4_ddr DDRD #define lcd_D3_port PORTD // lcd D3 connection #define lcd_D3_bit PORTD3 #define lcd_D3_ddr DDRD #define lcd_D2_port PORTD // lcd D2 connection #define lcd_D2_bit PORTD2 #define lcd_D2_ddr DDRD #define lcd_D1_port PORTD // lcd D1 connection #define lcd_D1_bit PORTD1 #define lcd_D1_ddr DDRD #define lcd_D0_port PORTD // lcd D0 connection #define lcd_D0_bit PORTD0 #define lcd_D0_ddr DDRD #define lcd_E_port PORTB // lcd Enable pin #define lcd_E_bit PORTB1 #define lcd_E_ddr DDRB #define lcd_RS_port PORTB // lcd Register Select pin #define lcd_RS_bit PORTB0 #define lcd_RS_ddr DDRB #define lcd_RW_port PORTB // lcd Read/Write pin #define lcd_RW_bit PORTB2 #define lcd_RW_ddr DDRB // LCD module information #define lcd_LineOne 0x00 // start of line 1 #define lcd_LineTwo 0x40 // start of line 2 //#define lcd_LineThree 0x14 // start of line 3 (20x4) //#define lcd_lineFour 0x54 // start of line 4 (20x4) //#define lcd_LineThree 0x10 // start of line 3 (16x4) //#define lcd_lineFour 0x50 // start of line 4 (16x4) // LCD instructions #define lcd_Clear 0b00000001 // replace all characters with ASCII 'space' #define lcd_Home 0b00000010 // return cursor to first position on first line #define lcd_EntryMode 0b00000110 // shift cursor from left to right on read/write #define lcd_DisplayOff 0b00001000 // turn display off #define lcd_DisplayOn 0b00001100 // display on, cursor off, don't blink character #define lcd_FunctionReset 0b00110000 // reset the LCD #define lcd_FunctionSet8bit 0b00111000 // 8-bit data, 2-line display, 5 x 7 font #define lcd_SetCursor 0b10000000 // set cursor position // Program ID uint8_t program_author[] = "Donald Weiman"; uint8_t program_version[] = "LCD-AVR-8f (gcc)"; uint8_t program_date[] = "Sep 16, 2013"; // Function Prototypes void lcd_write_8(uint8_t); void lcd_write_instruction_8f(uint8_t); void lcd_write_character_8f(uint8_t); void lcd_write_string_8f(uint8_t *); void lcd_init_8f(void); void lcd_check_BF_8(void); /******************************* Main Program Code *************************/ int main(void) { // configure the microprocessor pins for the data lines lcd_D7_ddr |= (1<<lcd_D7_bit); // 8 data lines - output lcd_D6_ddr |= (1<<lcd_D6_bit); lcd_D5_ddr |= (1<<lcd_D5_bit); lcd_D4_ddr |= (1<<lcd_D4_bit); lcd_D3_ddr |= (1<<lcd_D3_bit); lcd_D2_ddr |= (1<<lcd_D2_bit); lcd_D1_ddr |= (1<<lcd_D1_bit); lcd_D0_ddr |= (1<<lcd_D0_bit); // configure the microprocessor pins for the control lines lcd_E_ddr |= (1<<lcd_E_bit); // E line - output lcd_RS_ddr |= (1<<lcd_RS_bit); // RS line - output lcd_RW_ddr |= (1<<lcd_RW_bit); // RW line - output // initialize the LCD controller as determined by the defines (LCD instructions) lcd_init_8f(); // initialize the LCD display for an 8-bit interface // display the first line of information lcd_write_string_8f(program_author); // set cursor to start of second line lcd_check_BF_8(); // make sure LCD controller is ready lcd_write_instruction_8f(lcd_SetCursor | lcd_LineTwo); // display the second line of information lcd_write_string_8f(program_version); // endless loop while(1); return 0; } /******************************* End of Main Program Code ******************/ /*============================== 8-bit LCD Functions ======================*/ /* Name: lcd_init_8f Purpose: initialize the LCD module for a 8-bit data interface Entry: equates (LCD instructions) set up for the desired operation Exit: no parameters Notes: uses the busy flag instead of time delays when possible */ void lcd_init_8f(void) { // Power-up delay _delay_ms(100); // initial 40 mSec delay // Reset the LCD controller lcd_write_instruction_8f(lcd_FunctionReset); // first part of reset sequence _delay_ms(10); // 4.1 mS delay (min) lcd_write_instruction_8f(lcd_FunctionReset); // second part of reset sequence _delay_us(200); // 100uS delay (min) lcd_write_instruction_8f(lcd_FunctionReset); // third part of reset sequence _delay_us(200); // this delay is omitted in the data sheet // Function Set instruction lcd_write_instruction_8f(lcd_FunctionSet8bit); // set mode, lines, and font // --> from this point on the busy flag is available <-- // The next three instructions are specified in the data sheet as part of the initialization routine, // so it is a good idea (but probably not necessary) to do them just as specified and then redo them // later if the application requires a different configuration. // Display On/Off Control instruction lcd_check_BF_8(); // make sure LCD controller is ready lcd_write_instruction_8f(lcd_DisplayOff); // turn display OFF // Clear Display instruction lcd_check_BF_8(); // make sure LCD controller is ready lcd_write_instruction_8f(lcd_Clear); // clear display RAM // ; Entry Mode Set instruction lcd_check_BF_8(); // make sure LCD controller is ready lcd_write_instruction_8f(lcd_EntryMode); // set desired shift characteristics // This is the end of the LCD controller initialization as specified in the data sheet, but the display // has been left in the OFF condition. This is a good time to turn the display back ON. // Display On/Off Control instruction lcd_check_BF_8(); // make sure LCD controller is ready lcd_write_instruction_8f(lcd_DisplayOn); // turn the display ON } /*........................................................................... Name: lcd_write_string_8f ; Purpose: display a string of characters on the LCD Entry: (theString) is the string to be displayed Exit: no parameters Notes: uses the busy flag instead of time delays */ void lcd_write_string_8f(uint8_t theString[]) { volatile int i = 0; // character counter*/ while (theString[i] != 0) { lcd_check_BF_8(); // make sure LCD controller is ready lcd_write_character_8f(theString[i]); i++; } } /*........................................................................... Name: lcd_write_character_8f Purpose: send a byte of information to the LCD data register Entry: (theData) is the information to be sent to the data register Exit: no parameters Notes: configures RW (busy flag is implemented) */ void lcd_write_character_8f(uint8_t theData) { lcd_RW_port &= ~(1<<lcd_RW_bit); // write to LCD module (RW low) lcd_RS_port |= (1<<lcd_RS_bit); // select the Data Register (RS high) lcd_E_port &= ~(1<<lcd_E_bit); // make sure E is initially low lcd_write_8(theData); // write the data } /*........................................................................... Name: lcd_write_instruction_8f Purpose: send a byte of information to the LCD instruction register Entry: (theInstruction) is the information to be sent to the instruction register Exit: no parameters Notes: configures RW (busy flag is implemented) */ void lcd_write_instruction_8f(uint8_t theInstruction) { lcd_RW_port &= ~(1<<lcd_RW_bit); // write to LCD module (RW low) lcd_RS_port &= ~(1<<lcd_RS_bit); // select the Instruction Register (RS low) lcd_E_port &= ~(1<<lcd_E_bit); // make sure E is initially low lcd_write_8(theInstruction); // write the instruction } /*........................................................................... Name: lcd_write_8 Purpose: send a byte of information to the LCD module Entry: (theByte) is the information to be sent to the desired LCD register RS is configured for the desired LCD register E is low RW is low Exit: no parameters Notes: use either time delays or the busy flag */ void lcd_write_8(uint8_t theByte) { lcd_D7_port &= ~(1<<lcd_D7_bit); // assume that data is '0' if (theByte & 1<<7) lcd_D7_port |= (1<<lcd_D7_bit); // make data = '1' if necessary lcd_D6_port &= ~(1<<lcd_D6_bit); // repeat for each data bit if (theByte & 1<<6) lcd_D6_port |= (1<<lcd_D6_bit); lcd_D5_port &= ~(1<<lcd_D5_bit); if (theByte & 1<<5) lcd_D5_port |= (1<<lcd_D5_bit); lcd_D4_port &= ~(1<<lcd_D4_bit); if (theByte & 1<<4) lcd_D4_port |= (1<<lcd_D4_bit); lcd_D3_port &= ~(1<<lcd_D3_bit); if (theByte & 1<<3) lcd_D3_port |= (1<<lcd_D3_bit); lcd_D2_port &= ~(1<<lcd_D2_bit); if (theByte & 1<<2) lcd_D2_port |= (1<<lcd_D2_bit); lcd_D1_port &= ~(1<<lcd_D1_bit); if (theByte & 1<<1) lcd_D1_port |= (1<<lcd_D1_bit); lcd_D0_port &= ~(1<<lcd_D0_bit); if (theByte & 1<<0) lcd_D0_port |= (1<<lcd_D0_bit); // write the data // 'Address set-up time' (40 nS) lcd_E_port |= (1<<lcd_E_bit); // Enable pin high _delay_us(1); // implement 'Data set-up time' (80 nS) and 'Enable pulse width' (230 nS) lcd_E_port &= ~(1<<lcd_E_bit); // Enable pin low _delay_us(1); // implement 'Data hold time' (10 nS) and 'Enable cycle time' (500 nS) } /*........................................................................... Name: lcd_check_BF_8 Purpose: check busy flag, wait until LCD is ready Entry: no parameters Exit: no parameters Notes: main program will hang if LCD module is defective or missing data is read while 'E' is high */ void lcd_check_BF_8(void) { uint8_t busy_flag_copy; // busy flag 'mirror' lcd_D7_ddr &= ~(1<<lcd_D7_bit); // set D7 data direction to input lcd_RS_port &= ~(1<<lcd_RS_bit); // select the Instruction Register (RS low) lcd_RW_port |= (1<<lcd_RW_bit); // read from LCD module (RW high) do { busy_flag_copy = 0; // initialize busy flag 'mirror' lcd_E_port |= (1<<lcd_E_bit); // Enable pin high _delay_us(1); // implement 'Delay data time' (160 nS) and 'Enable pulse width' (230 nS) busy_flag_copy |= (lcd_D7_pin & (1<<lcd_D7_bit)); // get actual busy flag status lcd_E_port &= ~(1<<lcd_E_bit); // Enable pin low _delay_us(1); // implement 'Address hold time' (10 nS), 'Data hold time' (10 nS), and 'Enable cycle time' (500 nS ) } while (busy_flag_copy); // check again if busy flag was high // arrive here if busy flag is clear - clean up and return lcd_RW_port &= ~(1<<lcd_RW_bit); // write to LCD module (RW low) <-- (not really necessary) lcd_D7_ddr |= (1<<lcd_D7_bit); // reset D7 data direction to output }